Dodge Sprinter prices

Cummings Mobility Conversion & Supply (Cummings) is recalling certain model year 2006-2014 Ford E-150, E-250, E-350, Chevrolet Express, 2006-2008 Dodge Sprinter, and 2009-2014 Mercedes-Benz Sprinter, and 2013 Ford Transit Connect vehicles manufactured January 1, 2006, to October 8, 2014, equipped with certain model S2005, S2010, S5005, S5010, S5505, and S5510 wheelchair lifts manufactured by Ricon Corporation after January 1, 2006. The platform side plate of the affected wheelchair lifts may crack.

MERCEDES-BENZ USA (MBUSA) IS RECALLING CERTAIN MODEL YEAR 2002- 2003 SPRINTER 2500 AND 3500 VANS SOLD AS DODGE AND FREIGHTLINER VEHICLES. THE INTAKE MANIFOLDS MAY HAVE CORRODED. A CHEMICAL REACTION INVOLVING SULFUR IN THE DIESEL FUEL THAT TAKES PLACE UNDER CERTAIN CONDITIONS CAN LEAD TO THE FORMATION OF SULFURIC ACID IN THE EXHAUST CHANNEL OF THE INTAKE MANIFOLD.

MERCEDES-BENZ IS RECALLING CERTAIN MODEL YEAR 2008-2011 2500 AND 3500 SPRINTER VEHICLES EQUIPPED WITH AN OPTIONAL THREE-SEAT BENCH IN THE PASSENGER COMPARTMENT. THE SEAT BENCHES IN THE SECOND SEATING ROW MAY HAVE BEEN EQUIPPED WITH SAFETY BELTS THAT DO NOT MEET THE MINIMUM REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD 208, "OCCUPANT PROTECTION IN INTERIOR IMPACT," AND MOTOR VEHICLE SAFETY STANDARD 209, "SEAT BELT ASSEMBLIES." FIRST, THOSE SAFETY BELTS MAY NOT LOCK AS REQUIRED. SECOND, THE ASSEMBLY LOOP MAY NOT PERFORM TO MINIMUM FORCE REQUIREMENTS.

SPRINTER IS RECALLING CERTAIN MODEL YEAR 2009 AND 2010 VEHICLES MANUFACTURED FROM NOVEMBER 2009 THROUGH MARCH 2010 AND SOLD UNDER THE MERCEDES-BENZ, FREIGHTLINER, AND DODGE BRAND NAME. THE SPRING PLATE WHICH ATTACHES THE OIL FILLER NECK TO THE CYLINDER-HEAD COVER MAY CRACK.

Unavailability of MB Apps Complaint A popup is seen on the HU with the message "data connection temporarily not available". Cause MB Apps is officially sundowned for all vehicles with NTG5 Head Unit Variant. Remedy No support available for NTG5 Head Unit Variants for MB App related topics.

Complaint While driving through muddy / sandy/ off road terrain "4Matic Currently Unavailable" message on the dash Cause This vehicle is not equipped with a fixed force distribution AWD, rather force is only applied to the front axle according to ESP calculations. As per GF28.00‑D‑ 9900A: "vehicles with 4MATIC all‑wheel system and variable force distribution, an electronically regulated multiplate clutch integrated into the transfer case provides for the torque distribution. If the multiplate clutch is open during normal driving operation, only the rear axle drives the vehicle. If the clutch is closed, the front axle comes into play." The message "All‑wheel drive temporarily unavailable" is not indicative of a malfunction but rather informs the driver that all‑wheel drive is currently not available due to the transfer case clutch overheating. This occurs when the vehicle is driven in such a way that maximum front axle torque is needed for an extended period, causing the clutch to get e

ASSYST PLUS service reminder appears earlier than expected due to vehicle operating conditions Complaint The ASSYST PLUS service reminder appears earlier than expected. The customer or dealer may report that the vehicle did not reach the starting maintenance interval shown in vehicle documentation, option coding, sales literature, or the Owner's Manual. The service reminder may appear significantly earlier than anticipated even though no faults are stored and no malfunction is present in the vehicle. The remaining distance and remaining time continue to decrease normally until the service reminder is displayed. Cause This condition is not caused by a malfunction of ASSYST PLUS. ASSYST PLUS is a dynamic maintenance management system that continuously evaluates vehicle usage and opera-ting conditions to determine maintenance requirements. The starting maintenance interval specified by variant coding represents a maximum interval that may only be achieved under favorable operating conditi

Complaint Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes PDF document in attachments. Complaint C: One or more electrical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of electrical fault codes PDF document attached. NOTE: This LI supersedes LI14.20-N-073813, which is no longer valid. Cause Cause of Complaint A: Increased friction between the EGR Valve blade and seat due to soot deposits causing a delay of the EGR Valve being able to reach the target value of the EGR Valve position controller. NOTE: This causes the EGR Valve blade and potentially the boost pressure control

OM642 DPF Filter Cracked or Broken Complaint Vehicle will not start or exhibits noisy exhaust. Check Engine Lamp (CEL) is on. Multiple control unit communication and system faults may be present, including but not limited to: 134800, 134900, 11B300, 11EC00, 15E100, 155700, 162500. Additional events codes may include: 134300, 102200, 163400, 16CE00. In many cases, multiple unrelated faults are stored due to electrical disruption from wiring damage rather than indivi-dual component failure. Cause The DPF filter is cracked, broken, or leaking, allowing hot exhaust gas to escape from the exhaust system. Depending on the location of the break or leak, hot exhaust gas may be directed toward the main wiring harness and/ or the SCR (Selective Catalytic Reduction) dosing valve assembly. This heat exposure can result in: • Internal melting of wiring insulation within the harness • Short to ground conditions and loss of communication between control units • Damage to the dosing valve and/or heate

Complaint Rattling noise from underneath the vehicle. Cause One or more of the following conditions may be present: 1. The exhaust bracket from the DPF to the transmission is cracked or broken. • See Pic. 1 for an example of a broken bracket. 2. Transmission bell housing cracked or broken at the exhaust mounting area. • See Pic. 2 for an example of bell housing damage. 3. Exhaust bracket from DPF to engine (cylinder crankcase) cracked or broken. • See EPC OM651 #217 for bracket location. 4. Diesel Particulate Filter (DPF) pipe cracked at a weld joint. • Cracking may be present at bracket welds or along the DPF housing seams. • This can cause rattling noises and secondary exhaust bracket stress. • Perform a visual inspection of the DPF pipe and weld joints. Remedy Inspect all related components and repair or replace as required. Inspection and Repair 1. Inspect the exhaust bracket from the DPF to the transmission. • Check the bracket for cracks or complete separation. • See Pic. 1 for a