Freightliner Sprinter prices

Daimler Vans USA, LLC (DVUSA) is recalling certain 2021 Freightliner Sprinter and 2021-2023 Mercedes-Benz Sprinter and Metris vehicles. The fuel pump may shutdown, which can result in a loss of drive power.

Daimler Vans USA, LLC (DVUSA) is recalling certain 2019-2022 Mercedes-Benz Sprinter and 2019-2021 Freightliner Sprinter vehicles. The instrument cluster may fail to display any information when the vehicle is started.

Daimler Vans USA, LLC (DVUSA) is recalling certain 2019-2020 Mercedes-Benz Sprinter VS30 and Freightliner Sprinter VS30 vehicles. The heating, ventilation, and air conditioning (HVAC) blower motor circuit may be inadequate, which can allow the wiring harness to overheat.

Daimler Vans USA, LLC (DVUSA) is recalling certain 2019-2022 Mercedes-Benz Sprinter and Freightliner Sprinter vehicles equipped with a manual parking brake and 7-speed automatic transmission. The guide bushing on the parking pawl may fatigue, which can cause the parking pawl not to engage and result in vehicle rollaway.

Sprinter 907 ‑ Oil leak in area of wheel hub / rear axle shaft Complaint Oil leak in the area of the wheel hub Cause Insufficient sealing with previous axle shaft with single sealing lip Remedy New axle shafts have been created with a dual lip style seal. New part numbers: A 906 350 37 10 ‑‑> A 907 350 19 03 ( left / ring gear 215 ) A 906 350 38 10 ‑‑> A 907 350 20 03 ( right / ring gear 215 ) A 906 350 39 10 ‑‑> A 907 350 21 03 ( left / ring gear 245 ) A 906 350 40 10 ‑‑> A 907 350 22 03 ( right / ring gear 245 )

Check engine light with reduced power with fault codes P300A6D, P300974, P300DFB, or P300DE8 Complaint The check engine light is activated, accompanied by one or more of the following fault codes related to the boost pressure positioner: • P300A6D: The boost pressure is too low. Charge air cooler. • P300A6F: The boost pressure is too low. (High‑pressure turbocharger) • P300A71: The boost pressure is too low. (Low‑pressure turbocharger) • P300974: Component 'Boost pressure positioner' has a malfunction. The boost pressure is too low. • P300DFB: Component 'Boost pressure positioner' has a malfunction. • P300DE8: Boost pressure control A has a malfunction after a cold start. Cause The potential causes for these fault codes are: A. Leak or Blockage in the Intake or Charge Air System: This can prevent proper airflow, affecting boost pressure. B. Insufficient Source Vacuum, Vacuum Leak, or Sticking/Weak Vacuum Component: These issues can prevent the boost pressure positioner from functioning

EGR Valve Diagnosis & Cleaning (and EGR Cooler Cleaning) – OM642, Sprinter 906/907 Complaint Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes PDF document in attachments. Complaint C: One or more electrical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of electrical fault codes PDF document attached. NOTE: This LI supersedes LI14.20‑N‑073813, which is no longer valid. Cause Cause of Complaint A: Increased friction between the EGR Valve blade and seat due to soot deposits causing a delay of the EGR Valve being able to reach the target value of the EGR Valve position controlle

Acoustic Warning or message occurring when a closed sliding door is not recognized Complaint Customer may state the warning message or indicator accompanied by acoustic tone alerting the sliding door is ajar when the door is completely closed Cause There are several reasons that lead to the failure occurring: ‑ Mechanical damage through bending when loading and unloading ‑ Worn contact plates ‑‑> After detachment of silver plating, the coper plate is corroded ‑ Movement of sliding door/body when driving ‑‑> Contact pins do not always make contact with contact plate ‑‑> Central locking system fault message in instrument cluster Remedy In a problem case, replace contact switch for vehicles with +T50/+T55/+EL9 or contact plate with A4478201903 Check the fit of the sliding doors here and make any necessary adjustments as per AR72.16‑S‑1023E (447 /448) and AR72.16‑D‑1023TS (907/910). Further valid damage codes: 82326 Contact switch for central locking system on sliding door 82347 Contact pl

Roof‑mounted air conditioning system HK4 does not cool/cools poorly Complaint Roof‑mounted air conditioning system HK4 does not cool/cools poorly. Fault code in HVAC177: B106F87 The left rear blower regulator has a malfunction. Message missing. B107087 The right rear blower regulator has a malfunction. Message missing. Cause Condenser fans of roof‑mounted air conditioning system HK4 are not functioning. The fans themselves have a fault on the circuit board. As a result, an extremely rare interaction of various processes can lead to failure of the fans (software enters an undefined state). Remedy 1. Remove and reinsert the fuse for the condenser fans. 2. Activate the condenser fans via Xentry and check that they are operating correctly.

Brakes may lock up when reversing at slow speeds, 907 vehicles with modification year (XJ4) Complaint When reversing slowly, the vehicle erroneously triggers an emergency braking event, causing the brakes to lock up. Engine may not start following a key cycle. Cause The vehicle triggers a maneuvering or emergency braking event while reversing. The customer must then immediately park the vehicle (ignition Switched OFF) The hydraulic pressure release process within the ESP control unit may not be completed. Remedy Updating the software release of the RVC177 reversing camera