Mercedes-Benz CLE 300 prices

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2024 CLE 300 Convertible, CLE 300 Coupe, CLE 450 Convertible, CLE 450 Coupe, E 350, E 450 Station Wagon, E 450, and AMG CLE 53 Coupe vehicles. A software error in the MBUX multimedia system may deactivate certain vehicle systems, including the cross-traffic alert that applies the brakes automatically in certain driving situations.

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2023-2024 C300, AMG C43, S580e, S580, Maybach S580, Maybach S680, AMG SL43, AMGSL63, GLC300, EQE350, EQE500, EQS450, EQS580, AMG EQS, 2023 S500, AMG SL55, AMG EQE, 2024 E350, E450, AMG C63e S, CLE300 Coupe, CLE450 Coupe, and GLC300 Coupe vehicles. The 80-Amp fuses may have been manufactured incorrectly, which can cause the fuses to fail.

Complaint Oil seeping from turbocharger oil return line at connection to engine block. Low oil level warning. Oil observed under vehicle. Cause Return line under tension due to turbo rotation. Remedy Inspect turbocharger housing for rotation (refer to attachment). If rotation is confirmed, the turbocharger and oil return line must be replaced.‑Resealing or replacing only the oil return line is not sufficient and will not resolve the symptom.‑Clean noise insulation on right side of engine if necessary. Replace insulation if cleaning is not sufficient.‑Observe foot notes regarding additional parts in XENTRY parts information when ordering turbocharger.

Issue A software update will be performed that provides enhancements to the robustness and system stability of the communication module. The update is free of charge and runs in the background, which takes about 8 minutes to install. During this time, the vehicle can be driven without any restrictions, and the new software will be active with the next ignition cycle. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!