Mercedes-Benz CLS prices

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2001-2011 vehicles. The bonding between the glass panel and the sliding roof frame may deteriorate, possibly resulting in the glass panel detaching from the vehicle. For a full list of the affected models visit: https://static.nhtsa.gov/odi/rcl/2019/RMISC-19V918-4126.pdf

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit: https://static.nhtsa.gov/odi/rcl/2019/RMISC-19V787-4620.pdf

Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016 Mercedes Benz E350, E400, E400 4Matic, E63 4M S AMG, E350 4Matic, E63-4M S AMG, 2015 CLS400, CLS400 4Matic, CLS550, CLS63-4M "P" AMG, and CLS550 4Matic vehicles manufactured April 16, 2015, to April 22, 2015. The integral steel cable that secures the rubber seal to the bulkhead might have been damaged due to the supplier rework of the rubber seal. In the event the rubber seal is not properly secured around the engine compartment, it is possible for the rubber seal to temporarily stick to the hood when it is opened and then may fall into the engine bay when the hood is closed.

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2015 CLS 400 and CLS 400 4matic, 2012-2015 CLS 550 and CLS 550 4matic, 2012-2013 CLS 63, 2014 CLS 63, and 2014-2015 CLS 63P. The affected vehicles have LED tail lights that may not light on the sides, reducing the rear side visibility of the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 108, "Lamps, Reflective Devices, and Associated Equipment."

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2013-2015 E350 Sedan, E350 4Matic Sedan, E350 4Matic Station Wagon, E400 Hybrid Sedan, CLS 550 CGI, and CLS550 4Matic, 2013-2014 E550 4Matic Sedan, 2013 E63 Sedan, E63 Station Wagon and CLS63, 2014-2015 CLS63 4Matic, E63 4Matic Sedan, E63 4Matic Sedan "S", and E63 4Matic Station Wagon, 2015 CLS400, 2015 E400 Sedan, E400 4Matic Sedan and CLS400 4Matic and 2014 CLS63 "S". The affected vehicles have a rubber seal at the back of the engine bay that may temporarily stick to the hood when it is opened and then may fall into the engine bay when the hood is closed.

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side s

Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

Complaint The customer requests deactivation of the N112/9 HERMES communication module Note: Deactivation of the HERMES control unit (N112/9) is not supported for gray-market vehicles. Cause Before deactivating the HERMES control unit (N112/9), it must be clarified by the legal department of the respective MPC whether and under what conditions deactivation may be carried out. If deactivation is not permissible under applicable law, the HERMES control unit (N112/9) must not be deactivated. Remedy Please inform the customer that, following deactivation, the vehicle will no longer be able to place an automatic emergency call, nor will the customer be able to place a manual emergency call. After deactivation, the Mercedes-Benz Digital Extras will also no longer be available. Please have the attached sample form checked by your market's legal department, adapted to local requirements if necessary, and approved. Furthermore, after informing the customer about the effects of deactivation, ple

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blad

Complaint Noises at the front axle when cornering or maneuvering (video files attached) Note: Save video files locally and play them with Windows Media Player. Cause Driving with summer tires in combination with low outside temperatures. At low outside temperatures or in wet conditions, a noise may be produced at the outer wheel on the front axle while maneuvering with sharp steering angles. Note: AMG vehicles with 4MATIC of model series 217 (without code 494) and model series 222 have a modified axle geometry compared with series production vehicles to provide more sporty handling. The problem cannot be remedied by changing the axle settings.