Mercedes-Benz EQS 450+ prices

Mercedes-Benz USA, LLC (MBUSA) is recalling a certain 2023 EQS 450+ vehicle. The mounting brackets near the roof may have sharp edges that can damage the side-curtain air bag during deployment. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) numbers 214, "Side Impact Protection," and 226, "Ejection Mitigation."

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2024 EQE 350 4MATIC, EQE 350+, EQE 500 4MATIC, EQS 450 4MATIC, EQS 450+, EQS 580 4MATIC, AMG EQE 53 4MATIC, AMG EQS 53 4MATIC, 2023-2025 EQE SUV 350 4MATIC, EQE SUV 350+, EQE SUV 500 4MATIC, EQS SUV 450 4MATIC, EQS SUV 450+, EQS SUV 580 4MATIC, 2024-2025 EQS SUV 680 4MATIC, and AMG EQE SUV 53 4MATIC vehicles. The battery management system software may cause the high-voltage battery to shut down, which can result in a sudden loss of drive power.

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2022-2023 EQS450 and 2022 EQS580 vehicles. The bolts that secure the rear seat belt buckles to the body of the vehicle may not be secured properly.

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2022-2023 EQS 450, AMG EQS, EQS 580, and 2023 AMG EQE vehicles. A software error in the electric drivetrain may cause a loss of drive power.

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2022 EQS 450, EQS 580, 2023 Maybach S 580, Maybach S 680, and S 580e vehicles. The electronic stability program (ESP) software may malfunction, which can result in disabled vehicle dynamics control systems, including the anti-lock brake system, acceleration slip regulation, electronic stability program, and electronic brake force distribution (ABS, ASR, ESP, and EBD), as well as a vehicle speed display failure.

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2023 EQE 350, S580e, 2022-2023 EQS 450, EQS 580, 2022 AMG EQS 53, and EQS 450+ vehicles. The high-voltage battery monitoring system software may not alert the driver of a battery malfunction. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 305, "Electric-powered vehicles: Electrolyte Spillage and Electrical Shock Protection."

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is

Complaint Issue after OTA Update IC Odometer Reading blank("_ _ _ _") IC Maintanence data unavailable Cause OTA Update E61.0 Remedy In the IC Control Unit Log, please check the following information: Verify whether DTCs B228229, B228287, and B226656 are present in either A or A+S. Verify that Status Schlüssel‑ID = "ID is not valid" and Anlernstatus = "IC is initialized", as shown in the attached image (image_2). Please run the XENTRY guided test for the listed DTCs and provide the results.

Complaint Radio station cover art does not refresh when switching stations. The UI continues to show the old station’s artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. Please update the Head unit software to E505.9

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!