Mercedes-Benz GLC prices

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2023-2025 GLC 300, GLC 300 4MATIC, 2024-2025 AMG GLC 43 4MATIC, 2025 GLC 350E 4MATIC, and AMG GLC 63 S E vehicles equipped with a panoramic sunroof. In certain crash scenarios, where the rear occupant's head contacts the C-pillar, the pillar may not absorb an adequate amount of the impact. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 201, "Occupant Protection in Interior Impact."

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2022 GLC 300, 2020 GLC 350e, and 2020-2022 AMG GLC 43 vehicles. The headlights may be incorrectly adjusted too high and create a glare for oncoming traffic. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel to detach from the vehicle.

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020 GLC350E4 vehicles. The transmission wiring harness may be routed improperly, allowing it to chafe against the front drive shaft, which can cause loss of drive power.

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card software can cause a mobile network connection failure, disabling the emergency call (eCall) system.

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018-2021 CLA-Class, GLE/GLS-Class, A-Class, C-Class, E-Class, E-Class Coupe/Convertible, GLA/GLB-Class, GLC-Class, and CLS-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The rearview camera may not display the rearview image due to a software error. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint Mercedes-Benz USA is currently experiencing limited availability of transmission fluid specification ATF 236.17 due to a global supply constraint. 236.17 ATF 1L and 5L (PNs: A002989060312 and A002989060313) bottles are out of stock or in limited supply at Zep. This LI has been created with the following intention: - Provide dealers with additional workshop-focused guidance regarding the current ATF 236.17 supply constraint and the planned introduction of ATF 236.18. - Supplement existing communications and address common workshop questions related to maintenance, repairs, and fluid applicability. - Provide technical clarification and practical workshop guidance during the temporary supply constraint period. Dealers should continue to reference the latest News Channel Updates (NCUs) for the most current information regarding availability, ordering processes, supply status, and other related updates. Cause Damage to the Shell production facility has resulted in 236.17 oil suppl

• Always use the latest XENTRY Diagnosis software release with all available add-ons. • Make sure to follow the operation steps exactly as described in XENTRY Diagnosis! • Use a battery charger to ensure sufficient power supply of the vehicle on-board electrical system battery (greater than 12.5 V). • If XENTRY Diagnosis is already connected to the vehicle, start with operation step 2. If two or more software updates or SCN coding’s are performed during one workshop visit or SCN coding operations are performed, operation items 02-4762 and 02-5058 must only be invoiced once for each workshop order! Work Procedure: 1. Connect XENTRY Diagnosis. 2. Update engine electronics (ME) control unit software. To do so, select menu item "Quick test view → N3/10 - Engine electronics 'MED40' for combustion engine 'M274' (ME) → Adaptations → Control unit update → Update of control unit software". Then follow the user guidance in XENTRY Diagnosis. 3. Disconnect XENTRY Diagnosis.

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side s