Mercedes-Benz S 580 prices

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2022-2025 S-Class, EQE SUV, EQE, EQS SUV and EQS vehicles. Please see the recall report for a complete list of models. Software in the Acoustic Vehicle Alerting System (AVAS) may cause an incorrect external pedestrian warning sound while reversing. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 141, "Minimum Sound Requirements for Hybrid Electric Vehicles."

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2023-2024 C-Class, E-Class, S-Class, SL, GLC, EQE SUV, EQE, EQS SUV, and EQS vehicles that were incorrectly repaired under recall 24V-115. An incorrect fuse box that was not designed for the vehicle may have been installed.

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2022 S 500, Maybach S 580 4MATIC, 2021-2023 S 580 4MATIC, 2022 S 680 4MATIC, and 2023 S 580e 4MATIC vehicles. The front brake hoses may rupture and leak brake fluid.

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2024 GLC 300 4MATIC, and S 580 4MATIC vehicles. The bolts that secure the rear axle differential to the rear axle carrier may come loose, which can result in a separation of the drive shaft from the rear axle differential.

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 Maybach S 580 4MATIC, S 500 4MATIC, and S 580 4MATIC vehicles. The emergency call system may fail to place an automatic or manual call and may not provide the vehicle location as intended.

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2023 S580, and Maybach S580 vehicles. In the event of a mechanical failure in the engine Camtronic system, the engine control unit (ECU) software may cause the engine to overheat or stall.

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2023-2024 C300, AMG C43, S580e, S580, Maybach S580, Maybach S680, AMG SL43, AMGSL63, GLC300, EQE350, EQE500, EQS450, EQS580, AMG EQS, 2023 S500, AMG SL55, AMG EQE, 2024 E350, E450, AMG C63e S, CLE300 Coupe, CLE450 Coupe, and GLC300 Coupe vehicles. The 80-Amp fuses may have been manufactured incorrectly, which can cause the fuses to fail.

Issue A software update will be performed that provides enhancements to the robustness and system stability of the communication module. The update is free of charge and runs in the background, which takes about 8 minutes to install. During this time, the vehicle can be driven without any restrictions, and the new software will be active with the next ignition cycle. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

Issue On the subject vehicles, the transmission control unit (VGS) in the automatic transmission does not conform to current production specifications. It is possible that the polarities of the magnets in the transmission control unit (VGS) could have been incorrectly installed, leading to potential shift quality issues and gear lockouts. Remedy MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the software of the electric controller unit "fully integrated transmission control" in the affected vehicles.

Issue On the subject vehicles, the software of the electronic ignition switch control unit does not correspond to current production configuration. There is a possibility that various fault profiles may occur, such as sporadic discharge of the 12 V battery. Remedy MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the software of the EIS control unit in the affected vehicles.

Complaint Vehicle will not start after DC charging Warning in the instrument cluster related to High‑voltage on board electrical system The following fault codes related to stuck contactor can be found in the High Voltage Control units : PTCU ‑ N127 (Powertrain control unit) • P154900 ‑ There is a warning due to overcurrent in the charging system of the high‑voltage electric circuit. • P154A00 ‑ There is a warning due to a detected crash event at standstill. • P154B00 ‑ There is a warning due to a stuck contactor. DCB223 ‑ N116/5 (Direct current charge connection unit) • P0E8929 ‑ The input current of the on‑board DC charging connection unit is too high. There is an invalid signal. • P2BC500 ‑ The contact ''Positive terminal'' of the contactor in the on‑board DC current charge‑connection unit is jammed closed • P2BCC00 ‑ The contact ''Negative terminal'' of the contactor in the onboard DC current charge‑connection unit is jammed closed. Instrument cluster warning messages : Cause • Cur

Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.